A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
Listed here down the page you can locate lots of wonderful guidance all about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a bathtub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard job. If the old bathtub is easily accessible, the task can move immediately; if you have to open up a wall to get rid of the old tub and also place the new bathtub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Possibilities are you might require an expert plumber to make tube connections.
This post will assist you install a new bath tub in your bathroom if you have currently bought a new bathtub and don't require to change the plan of your previous water pipes.
Your devices as well as product checklist must comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines remain in area in between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the bath tub until the spirit level checks out degree.
To install faucets, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Switch on the water and inspect all joints and also new pipework for leakages and also tighten them if required. Fill up the tub as well as additionally check the overflow electrical outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling as well as securing around the bathtub must wait until the tub has actually been used a minimum of when as this will certainly settle it right into its last setting.
Getting ready for the Installation
To start with, the supporting frame provided with the bathroom should be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components as well as installations. They are offered in tubes and also cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can crack fairly early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark down below. We would be delighted to see your insights about this write-up. In hopes to see you back again in the near future. Enjoyed reading our content? Please share it. Let other people locate it. Thanks a lot for going through it.
Article
Report this page